Shure Microflex MX391 Series Instrukcja Użytkownika Pobierz pdf

Microflex

MX391BP Series

Boundary Microphones User Guide

27D3047 (Rev. 5)

5, Shure Incorporated

Printed in U.S.A.

GENERAL

Shure Microflex

MX391BP series microphones are small, sur-

face mounted electret condenser microphones designed for

mounting on conference tables, stage floors, and lecterns. Their

high sensitivity and wide frequency response make them especial-

ly suitable for picking up speech and vocals in sound reinforce-

ment and recording applications. The supplied MX1BP bat-

tery-powered preamplifier allows use of these microphones in sit-

uations where phantom power is not available.

FEATURES

• Flat frequency response across the vocal range for uncolored

sound

• Interchangeable cardioid, supercardioid, and omnidirectional

cartridges that provide optimal choice for anyapplication

• Sleek, low-profile design for unobtrusive appearance

• Balanced transformer output providesfor for increased

immunity to noise over long cable runs.

• MX1BP preamplifier features mic on/mute switch and power

LED indicator; works on either a 9 V battery or phantom power.

MODEL VARIATIONS

MX391BP models have a microphone an attached to a 43.7 meter

(12 ft) cable terminated with a female 4-pin mini connector. The

MX1BP preamplifier has an attached 3.7 m (12 ft) cable terminat-

ed with a 3-pin male XLR connector.

Microflex

boundary microphones come with one of three inter-

changeable cartridges, as indicated by the model number (found

on the bottom of the microphone base).

MX391/C or MX391W/C or MX391BLP/C. Cardioid pickup pat-

tern for general sound reinforcement applications. Pickup angle (-

3 dB) = 130°.

MX391/S or MX391W/S or MX391BLP/S. Supercardioid pickup

pattern for sound reinforcement applications requiring narrow or

more distant coverage. Pickup angle (-3 dB) = 115°.

MX391/O or MX391W/O or MX391BLP/O. Omnidirectional pick-

up pattern for recording or remote monitoring applications. Pickup

angle = 360°.

PERMANENT INSTALLATION

Screw holes in the microphone base and a bottom exit hole for the

microphone cable are provided for permanent installation of the

boundary microphone.

To re-route the microphone cable through

the bottom exit hole, use the following steps:

To re-route the microphone cable through the bottom exit hole,

use the following steps:

1. Remove the grille from the microphone base by loosening the

single screw on top of the grille.

2. Remove the 4-pin mini connector from the end of the cable by

cutting the cable just below the connector.

WARNING: Do not attempt to detach the cable from the micro-

phone interface.

3. Re-route cable as shown in Figure 1.

4. After threading the cable through the bottom exit hole in the

mounting surface, re-attach the 4-pin mini connector

(see Figure 4).

REPAINTING THE MX391BP

Before applying paint to the MX391BP series, remove the grille

from the base, remove the foam from the inside of the grille, and

mask the microphone cartridge and interface. Also, mask the ca-

ble where necessary.

BATTERY INSTALLATION (Figure 2)

1. Move the Mic Mute/On switch on the preamplifier to the Mute

position.

2. Press down on the OPEN side of the battery compartment cov-

er. Slide the cover back and flip it open.

3. Insert a 9 V battery as shown, observing proper battery polarity

(“+/-”). Close the battery compartment cover.

4. Move the Mic Mute/On switch on the preamplifier to the On po-

sition when ready to use the system.

NOTE: A minimal power drain occurs while the 9 V battery is

installed. To conserve battery life, remove the battery when the

preamplifier is not in use.

Service

Loop

Screw Hole

Microphone

Interface

Strain Relief Post

Bottom

Exit Hole

Top Exit

Hole

FIGURE 1

–+

FIGURE 2

1 2 3

Podsumowanie treści

Strona 1 - MX391BP Series

Strona 2 - FIGURE 4

2OPERATION OF MX1BP PREAMPLIFIER (Figure 3)1. With the Mic Mute/On switch in the Mute position, plug the mi-crophone into the preamplifier's 4-pi

Strona 3

3MX1BP Input ConfigurationUnbalancedMX1BP Output ConnectorMale 3-pin XLRMX1BP Output ConfigurationTransformer-BalancedCertificationMeets European Unio

Więcej dokumentów dla Mikrofony Shure Microflex MX391 Series

Aby wyświetlić dokument Shure Microflex MX391 Series Instrukcja Użytkownika

Shure Microflex MX391 Series Instrukcja Użytkownika (16 strony)

Shure Microflex MX391 Series Instrukcja Użytkownika (12 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Shure Microflex MX391 Series Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Mikrofony Shure Microflex MX391 Series. Microflex MX391BP Series Boundary Microphones User Guide [en] Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Mikrofony Shure Microflex MX391 Series

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Mikrofony Shure Microflex MX391 Series